PCN400型全自動運動粘度測定儀
設備采用了模塊化設計，檢測部分采用了先進的傳感器和高精度AD轉換電路，主控部分采用了多個工業應用、高可靠性16位RISC結構、超低功耗微處理器，良好可靠的通訊將各模塊組成一個統一的、可靠的測控平臺。
設備運行程序，采用高質量、最簡捷的模塊化程序設計，并與硬件有機的結合，使得運動黏度測定過程的全自動升溫和恒溫、液位檢測、計時、清洗黏度管、打印等全部工作全自動完成，達到了一鍵出結果的操作方式。
設備預設了4組測定參數，供檢測不同試樣時選用，便于檢測操作。同時預設參數具有可修改性，來滿足測定特殊試樣的要求。
設備具有出廠設置值恢復功能，當設置調整不當時，可選擇"恢復出廠設置"選項恢復正常的工作狀態。同時儀器內部的自檢功能確保了工作長期連續的可靠性。
特點
•良好人機界面，方便操作
•一鍵完成運動黏度測定，簡化操作
•四組預置參數，供選用
•可修改預置參數，適應特殊要求
•紅外液位檢測不受室內光線、燈光干擾
•液位檢測位置可調整，靈活自如
•全部模塊化設計穩定、可靠性高
•全自動儲存100個檢測結果，并隨時查看或打印
•檢測過程遵守標準規定，數據可靠
•檢測方法可靠，重復性好
•可長期連續工作，故障率極低
執行標準： GB/T265
技術參數
溫度范圍： 室溫～+100°C 精度±0.01°C。
溫度傳感器： 德國進口的Pt 100不銹鋼探頭， 內置溫度校正，檢測結果可靠。
加熱方式： 電加熱單元，最大加熱功率1500 W，可編程控制加熱速率。
液位檢測： 紅外光電檢測。
顯 示： 7寸彩色觸摸屏。
溫度校正： 全自動校正，可編程校正。
數據存儲： 100測試結果。
電 源： AC220V 50Hz。最大功率1500 W
使用環境溫度：10～40℃
存儲環境溫度：0～50℃
PCN400 Automatic Viscosity Tester
The equipment adopts a modular design. The detection part adopts advanced sensors and high-precision AD conversion circuits. The main control part adopts a number of industrial applications, high-reliability 16-bit RISC architecture, ultra-low-power microprocessors, and is reliable and reliable. Communications will form a unified and reliable monitoring and control platform for each module.
The equipment operation program adopts high quality and simplest modular program design, and is organically combined with hardware. It makes full automatic temperature rise and constant temperature, liquid level detection, timing, cleaning viscosity tube, printing, etc. of the kinematic viscosity measurement process. Automatically completed, to achieve a one-button operation method.
The device presets four sets of measurement parameters for use when testing different samples for ease of detection. At the same time, the preset parameters are modifiable to meet the requirements for the determination of special samples.
The device has a factory set value recovery function. When the settings are adjusted incorrectly, the "restore factory settings" option can be selected to restore normal working conditions. At the same time, the internal self-test function of the instrument ensures the long-term continuous reliability of the work.
Features
• Good man-machine interface, easy to operate
• One-touch kinematic viscosity measurement simplifies operation
• Four preset parameters for selection
• Can modify preset parameters to meet special requirements
• IR level detection is not affected by indoor light and light interference
• The liquid level detection position can be adjusted, flexible and flexible
• All modular design is stable and reliable
• Fully automatic storage of 100 test results and viewing or printing at any time
• The inspection process complies with the standards and the data is reliable
• reliable detection method, good repeatability
• It can work continuously for a long time and the failure rate is extremely low
Executive Standard: GB/T265
Technical Parameters
Temperature range: room temperature ~ +100 °C Accuracy ± 0.01 °C.
Temperature sensor: Pt 100 stainless steel probe imported from Germany, built-in temperature correction, reliable test results.
Heating method: electric heating unit, maximum heating power 1500 W, programmable heating rate.
Level detection: infrared photoelectric detection.
Display: 7-inch color touch screen.
Temperature correction: automatic correction, programmable correction.
Data storage: 100 test results.
Power source: AC220V 50Hz. Maximum power 1500 W
Ambient temperature: 10～40°C
Storage environment temperature: 0 ~ 50 °C |
